If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Visio Generated Web Page Issue
Hello.
I use Vision 2007 to build a web site. The website consists of 4 pages (Home, Products, Services, Contact) and I have navigation buttons for each of these pages. When I open the page, it displays a frame on the left hand side of the page with links for each page. The main page is displayed with 2 inch left, bottom and right margins. I am not proficient with HTML so was hoping to be able to remove the navigation frame and margins within Visio. Is that possible? Thanks a ton. |
#2
|
|||
|
|||
Visio Generated Web Page Issue
Hi,
If I understand you correctly then you just need ensure that none of the checkboxes, under 'Publishing Options' (on the General tab), are ticked. This will produce a page with toolbar frame of zero pixels (width). Note that to get to the above checkboxes you have to click the 'Publish...' button on the Save As Web Page 'Save As' dialog. Hope that helps. Best regards John John Goldsmith (Visio MVP) www.visualSignals.typepad.co.uk www.visualSignals.co.uk "aball65" wrote in message news Hello. I use Vision 2007 to build a web site. The website consists of 4 pages (Home, Products, Services, Contact) and I have navigation buttons for each of these pages. When I open the page, it displays a frame on the left hand side of the page with links for each page. The main page is displayed with 2 inch left, bottom and right margins. I am not proficient with HTML so was hoping to be able to remove the navigation frame and margins within Visio. Is that possible? Thanks a ton. |
#3
|
|||
|
|||
Visio Generated Web Page Issue
JOHN,
What can we do if we want to INCREASE the size of the sidebar when the project is displayed as a web page? I want to increase it to 420px but can't find where I can change it to a static size. Thanks. BoLane "John Goldsmith_Visio_MVP" wrote: Hi, If I understand you correctly then you just need ensure that none of the checkboxes, under 'Publishing Options' (on the General tab), are ticked. This will produce a page with toolbar frame of zero pixels (width). Note that to get to the above checkboxes you have to click the 'Publish...' button on the Save As Web Page 'Save As' dialog. Hope that helps. Best regards John John Goldsmith (Visio MVP) www.visualSignals.typepad.co.uk www.visualSignals.co.uk "aball65" wrote in message news Hello. I use Vision 2007 to build a web site. The website consists of 4 pages (Home, Products, Services, Contact) and I have navigation buttons for each of these pages. When I open the page, it displays a frame on the left hand side of the page with links for each page. The main page is displayed with 2 inch left, bottom and right margins. I am not proficient with HTML so was hoping to be able to remove the navigation frame and margins within Visio. Is that possible? Thanks a ton. |
#4
|
|||
|
|||
Visio Generated Web Page Issue
Hello BOLANE,
I've answered this on your "Change the width of toolbar in IE when saved as web page" post above. Best regards John John Goldsmith (Visio MVP) www.visualSignals.typepad.co.uk www.visualSignals.co.uk "BoLane" wrote in message ... JOHN, What can we do if we want to INCREASE the size of the sidebar when the project is displayed as a web page? I want to increase it to 420px but can't find where I can change it to a static size. Thanks. BoLane "John Goldsmith_Visio_MVP" wrote: Hi, If I understand you correctly then you just need ensure that none of the checkboxes, under 'Publishing Options' (on the General tab), are ticked. This will produce a page with toolbar frame of zero pixels (width). Note that to get to the above checkboxes you have to click the 'Publish...' button on the Save As Web Page 'Save As' dialog. Hope that helps. Best regards John John Goldsmith (Visio MVP) www.visualSignals.typepad.co.uk www.visualSignals.co.uk "aball65" wrote in message news Hello. I use Vision 2007 to build a web site. The website consists of 4 pages (Home, Products, Services, Contact) and I have navigation buttons for each of these pages. When I open the page, it displays a frame on the left hand side of the page with links for each page. The main page is displayed with 2 inch left, bottom and right margins. I am not proficient with HTML so was hoping to be able to remove the navigation frame and margins within Visio. Is that possible? Thanks a ton. |
Thread Tools | |
Display Modes | |
|
|