|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
June 29th, 2004, 07:07 PM
|
|||
|
|||
Can't move fields with UpDownLeftRight Keys
In design view, I cannot move "highlighted fields" via pressing any of the
Up/Down or Left/Right keys. I have used this function before and it always came in very handy. Are there specific settings (for PC or Access) that need to be set in order to utilize this feature? Tom 
|
|
#2
June 29th, 2004, 09:58 PM
|
|||
|
|||
|
Can't move fields with UpDownLeftRight Keys
I'm not aware of any setting that would affect this. Are you sure that one
of the controls you have selected isn't against the edge of the form, and therefore can't be moved any further? Tom wrote: In design view, I cannot move "highlighted fields" via pressing any of the Up/Down or Left/Right keys. I have used this function before and it always came in very handy. Are there specific settings (for PC or Access) that need to be set in order to utilize this feature? Tom -- Joan Wild Microsoft Access MVP
|
|
#3
June 29th, 2004, 11:15 PM
|
|||
|
|||
|
Can't move fields with UpDownLeftRight Keys
Yes, none of the boxes touch the edges of a form. Thanks for the info
anyhow... now I know at least where I stand w/ this problem. -- Thanks, Tom "Joan Wild" wrote in message ... I'm not aware of any setting that would affect this. Are you sure that one of the controls you have selected isn't against the edge of the form, and therefore can't be moved any further? Tom wrote: In design view, I cannot move "highlighted fields" via pressing any of the Up/Down or Left/Right keys. I have used this function before and it always came in very handy. Are there specific settings (for PC or Access) that need to be set in order to utilize this feature? Tom -- Joan Wild Microsoft Access MVP
|
|
#4
June 30th, 2004, 01:23 PM
|
|||
|
|||
|
Can't move fields with UpDownLeftRight Keys
It's possible that when you selected the group of boxes, you also selected a
line that's up against the section border. These can sometimes be difficult to see, and often are against the left edge of the form. -- Joan Wild Microsoft Access MVP Tom wrote: Yes, none of the boxes touch the edges of a form. Thanks for the info anyhow... now I know at least where I stand w/ this problem. "Joan Wild" wrote in message ... I'm not aware of any setting that would affect this. Are you sure that one of the controls you have selected isn't against the edge of the form, and therefore can't be moved any further? Tom wrote: In design view, I cannot move "highlighted fields" via pressing any of the Up/Down or Left/Right keys. I have used this function before and it always came in very handy. Are there specific settings (for PC or Access) that need to be set in order to utilize this feature? Tom -- Joan Wild Microsoft Access MVP
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| UNION Query truncating Memo fields | Matthew DeAngelis | Running & Setting Up Queries | 4 | June 10th, 2004 02:17 PM |
| Hot key's | Antonio | General Discussion | 5 | June 8th, 2004 12:54 PM |
| Lost text fields in merge | CGiannini | General Discussion | 5 | June 4th, 2004 10:23 PM |
| Lookup fields on label report | Howard | Setting Up & Running Reports | 1 | June 3rd, 2004 02:43 AM |
| Mail Merge two fields that have multiple lines with new line control code | Eric Li | Mailmerge | 7 | May 25th, 2004 06:10 PM |
Linear Mode
