|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
May 17th, 2006, 04:15 PM
posted to microsoft.public.access.reports
|
|||
|
|||
exporting problem
I am trying to export a report with the outputto function....
Here is the problem. - The report gets opened normally by passing an openarg argument. I don't believe the outputto function allows for these passing of variable options when trying to export a report. What can I do to pass the variables in at the same time or before the export takes place..... Report won't run - obviously - without the parameters I pass in normally.... ???? Thanks, Jason 
|
|
#2
May 17th, 2006, 04:49 PM
posted to microsoft.public.access.reports
|
|||
|
|||
|
exporting problem
"85ascMcLaren" wrote: I am trying to export a report with the outputto function.... Here is the problem. - The report gets opened normally by passing an openarg argument. I don't believe the outputto function allows for these passing of variable options when trying to export a report. What can I do to pass the variables in at the same time or before the export takes place..... Report won't run - obviously - without the parameters I pass in normally.... ???? Thanks, Jason If you open the report in preview on the screen, one has the option to right click and export it, so there must be a way (I would think) to export it by some command once has finished opening (processing) - then I could issue a close command to close the report.... Any suggestions on either this reasoning or my first one in my previous post ????? An answer to the first post would be my most hopeful solution, but at this point - I would take any solutions....
|
|
#3
May 17th, 2006, 07:13 PM
posted to microsoft.public.access.reports
|
|||
|
|||
|
exporting problem
"85ascMcLaren" wrote: "85ascMcLaren" wrote: I am trying to export a report with the outputto function.... Here is the problem. - The report gets opened normally by passing an openarg argument. I don't believe the outputto function allows for these passing of variable options when trying to export a report. What can I do to pass the variables in at the same time or before the export takes place..... Report won't run - obviously - without the parameters I pass in normally.... ???? Thanks, Jason If you open the report in preview on the screen, one has the option to right click and export it, so there must be a way (I would think) to export it by some command once has finished opening (processing) - then I could issue a close command to close the report.... Any suggestions on either this reasoning or my first one in my previous post ????? An answer to the first post would be my most hopeful solution, but at this point - I would take any solutions.... A simple solution is to make the variables global, BUT was wondering if another way using openargs method....
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Problem with exporting xls sheels to txt files separated by tabs | Piotr Krasnicki | Setting up and Configuration | 2 | February 6th, 2006 12:11 PM |
| Form size problem with exporting data | Andym | Using Forms | 2 | December 22nd, 2005 03:07 PM |
| Problem exporting email to excel... help! | Twins | General Discussion | 1 | August 26th, 2005 01:32 PM |
| Reinstalling OE... | KAR | Outlook Express | 24 | August 21st, 2004 06:52 PM |
| Productkey problem when installing office 2003 on network | Stefan Schreurs | Setup, Installing & Configuration | 1 | June 1st, 2004 11:16 PM |
Linear Mode
