If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
custom page size
would like to print receipts that are 5.5 high by 8.5 wide on dot matrix
using ncr paper. Found the printer... found the paper. but can't find a way to set the page size. Using Access 2007. Help!!! tnx |
#2
|
|||
|
|||
custom page size
You may be able to set a custom page size through the printer driver. Some
old dot matrix printers had drivers that did that. But 5.5" is half of an 11" page? Could you just set it for 11" paper, and then make the report fit 2-up on the page? -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. "Glen" wrote in message ... would like to print receipts that are 5.5 high by 8.5 wide on dot matrix using ncr paper. Found the printer... found the paper. but can't find a way to set the page size. Using Access 2007. Help!!! tnx |
#3
|
|||
|
|||
custom page size
Thought about that... printer driver doesn't appear to have custom setting.
2-up would be good but we're checking in on client at a time. You're right about older combinations. I was able to do this with an older epson (current is also epson)... was also using access 97 at the time. Rats! "Allen Browne" wrote: You may be able to set a custom page size through the printer driver. Some old dot matrix printers had drivers that did that. But 5.5" is half of an 11" page? Could you just set it for 11" paper, and then make the report fit 2-up on the page? -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. "Glen" wrote in message ... would like to print receipts that are 5.5 high by 8.5 wide on dot matrix using ncr paper. Found the printer... found the paper. but can't find a way to set the page size. Using Access 2007. Help!!! tnx |
#4
|
|||
|
|||
custom page size
I didn't follow why 2 records per 11" page would not work?
You just size your detail section so it fits 2 on a page (after subtracting the top and bottom margins.) If you are printing on pre-printed form, the only practical difficulty is spacing the 2 records equally if your driver does not support zero top and bottom margins. There is a way to do that with a faux-group footer, as explained he http://allenbrowne.com/ser-54.html -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. "Glen" wrote in message ... Thought about that... printer driver doesn't appear to have custom setting. 2-up would be good but we're checking in on client at a time. You're right about older combinations. I was able to do this with an older epson (current is also epson)... was also using access 97 at the time. Rats! "Allen Browne" wrote: You may be able to set a custom page size through the printer driver. Some old dot matrix printers had drivers that did that. But 5.5" is half of an 11" page? Could you just set it for 11" paper, and then make the report fit 2-up on the page? -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. "Glen" wrote in message ... would like to print receipts that are 5.5 high by 8.5 wide on dot matrix using ncr paper. Found the printer... found the paper. but can't find a way to set the page size. Using Access 2007. Help!!! tnx |
Thread Tools | |
Display Modes | |
|
|