If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Font formatting of index separators
I am creating a two-level index. For the top level I want the headwords in
bold, but not (for those entries without a sub-heading) the page numbers. The obvious method is to define the "Index 1" style as bold, and it is then easy to turn off bold for the page numbers. But I can't work out how to prevent the separator (a comma in my case) still showing as bold! The only workaround I can think of is to forget the idea of putting the bold font into the style definition and to embolden manually the relevant part of each XE field code. This seems very inelegant, as well as hard work! Can anyone do better? All ideas gratefully received! |
#2
|
|||
|
|||
If I were you, I would go with what works. This will be less work in the
long run than spinning your wheels trying to find the "elegant" solution. -- Suzanne S. Barnhill Microsoft MVP (Word) Words into Type Fairhope, Alabama USA Word MVP FAQ site: http://word.mvps.org Email cannot be acknowledged; please post all follow-ups to the newsgroup so all may benefit. "David Beamish" wrote in message ... I am creating a two-level index. For the top level I want the headwords in bold, but not (for those entries without a sub-heading) the page numbers. The obvious method is to define the "Index 1" style as bold, and it is then easy to turn off bold for the page numbers. But I can't work out how to prevent the separator (a comma in my case) still showing as bold! The only workaround I can think of is to forget the idea of putting the bold font into the style definition and to embolden manually the relevant part of each XE field code. This seems very inelegant, as well as hard work! Can anyone do better? All ideas gratefully received! |
#3
|
|||
|
|||
Alternatively, another functional workaround might be to Find commas in bold
and Replace them to commas not bold at the end of editing. Less hard work. Assuming there aren't too many headwords with commas that will need to be bold. If I were you, I would go with what works. This will be less work in the long run than spinning your wheels trying to find the "elegant" solution. I am creating a two-level index. For the top level I want the headwords in bold, but not (for those entries without a sub-heading) the page numbers. The obvious method is to define the "Index 1" style as bold, and it is then easy to turn off bold for the page numbers. But I can't work out how to prevent the separator (a comma in my case) still showing as bold! The only workaround I can think of is to forget the idea of putting the bold font into the style definition and to embolden manually the relevant part of each XE field code. This seems very inelegant, as well as hard work! Can anyone do better? All ideas gratefully received! -- Daiya Mitchell, MVP Mac/Word Word FAQ: http://www.word.mvps.org/ MacWord Tips: http://www.word.mvps.org/MacWordNew/ What's an MVP? A volunteer! Read the FAQ: http://mvp.support.microsoft.com/ |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Carrying over font formatting | Ronnie R. | General Discussion | 1 | May 25th, 2005 07:51 PM |
font color is the same in conditional formatting | AJ | Using Forms | 0 | April 27th, 2005 08:42 AM |
Formatting font and backfill on queries | Bettergains | Running & Setting Up Queries | 0 | November 10th, 2004 11:50 PM |
PiVot Table Formatting - Bold Font | plumstone | General Discussion | 0 | November 8th, 2004 02:39 PM |
Here's a shocker | Mike Labosh | General Discussion | 2 | October 26th, 2004 05:04 PM |