If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Change Page x of y to reflect only certain pages?
I am creating a template to use for a client and they would like to have page
x of y but not count the forematter. I have multiple sections, so is there a way to only count the number of pages from a certain point going forward? |
#2
|
|||
|
|||
Change Page x of y to reflect only certain pages?
Isn't this the same question asked in a different way?
Terry "stickcc" wrote in message ... I am creating a template to use for a client and they would like to have page x of y but not count the forematter. I have multiple sections, so is there a way to only count the number of pages from a certain point going forward? |
#3
|
|||
|
|||
Change Page x of y to reflect only certain pages?
I don't believe it is. I think the other question was asking how to insert
"page x of y" in 2007. My problem is Word counts all the pages in the document (or section if you use that field). My page numbering starts at 1 after the first ten pages of forematter and I didn't want to count those pages in the page x of y. I want y to = the number of pages after the forematter. I hope that explains what I need. "Terry Farrell" wrote: Isn't this the same question asked in a different way? Terry "stickcc" wrote in message ... I am creating a template to use for a client and they would like to have page x of y but not count the forematter. I have multiple sections, so is there a way to only count the number of pages from a certain point going forward? |
#4
|
|||
|
|||
Change Page x of y to reflect only certain pages?
So Sorry! The first time I tried to post this question I got an error to try
again later. Since I didn't remember exactly what I wrote, I did write it again. Thanks for your answer on the other post. "stickcc" wrote: I don't believe it is. I think the other question was asking how to insert "page x of y" in 2007. My problem is Word counts all the pages in the document (or section if you use that field). My page numbering starts at 1 after the first ten pages of forematter and I didn't want to count those pages in the page x of y. I want y to = the number of pages after the forematter. I hope that explains what I need. "Terry Farrell" wrote: Isn't this the same question asked in a different way? Terry "stickcc" wrote in message ... I am creating a template to use for a client and they would like to have page x of y but not count the forematter. I have multiple sections, so is there a way to only count the number of pages from a certain point going forward? |
#5
|
|||
|
|||
Change Page x of y to reflect only certain pages?
You're welcome. There is often quite a delay before a post appears and at
the moment there seems to be a sync problem between servers exaggerating the delay. But note that Macropod has replied with a better way to add the SECTIONPAGES field in the first section and hiding it. Terry "stickcc" wrote in message ... So Sorry! The first time I tried to post this question I got an error to try again later. Since I didn't remember exactly what I wrote, I did write it again. Thanks for your answer on the other post. "stickcc" wrote: I don't believe it is. I think the other question was asking how to insert "page x of y" in 2007. My problem is Word counts all the pages in the document (or section if you use that field). My page numbering starts at 1 after the first ten pages of forematter and I didn't want to count those pages in the page x of y. I want y to = the number of pages after the forematter. I hope that explains what I need. "Terry Farrell" wrote: Isn't this the same question asked in a different way? Terry "stickcc" wrote in message ... I am creating a template to use for a client and they would like to have page x of y but not count the forematter. I have multiple sections, so is there a way to only count the number of pages from a certain point going forward? |
Thread Tools | |
Display Modes | |
|
|