|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
December 13th, 2007, 07:03 PM
posted to microsoft.public.word.tables
|
|||
|
|||
How can I horizontally split a table (in WORD) into two tables?
I have a very long table that spans the length of several pages. How can I
split the table into multiple tables and have one table per page? 
|
|
#2
December 13th, 2007, 09:01 PM
posted to microsoft.public.word.tables
|
|||
|
|||
|
How can I horizontally split a table (in WORD) into two tables?
Click in the row above which you want to split the table. Then select Table
Split Table. This splits the table into two by inserting an empty paragraph between the tables. It may be a good idea to turn on non-printing characters (Ctrl+Shift+8) so that you can see the paragraph marks. -- Regards Lene Fredborg DocTools - Denmark www.thedoctools.com Document automation - add-ins, macros and templates for Microsoft Word "springoflife" wrote: I have a very long table that spans the length of several pages. How can I split the table into multiple tables and have one table per page?
|
|
#3
December 13th, 2007, 09:29 PM
posted to microsoft.public.word.tables
|
|||
|
|||
|
How can I horizontally split a table (in WORD) into two tables
Where is that option in WORD 2007? I can't find a "Split Table" command
anywhere. ? "Lene Fredborg" wrote: Click in the row above which you want to split the table. Then select Table Split Table. This splits the table into two by inserting an empty paragraph between the tables. It may be a good idea to turn on non-printing characters (Ctrl+Shift+8) so that you can see the paragraph marks. -- Regards Lene Fredborg DocTools - Denmark www.thedoctools.com Document automation - add-ins, macros and templates for Microsoft Word "springoflife" wrote: I have a very long table that spans the length of several pages. How can I split the table into multiple tables and have one table per page?
|
|
#4
December 13th, 2007, 09:51 PM
posted to microsoft.public.word.tables
|
|||
|
|||
|
How can I horizontally split a table (in WORD) into two tables
Hi springoflife,
It's on the Table Ribbon's Layout tab. Cheers -- macropod [MVP - Microsoft Word] ------------------------- "springoflife" wrote in message ... Where is that option in WORD 2007? I can't find a "Split Table" command anywhere. ? "Lene Fredborg" wrote: Click in the row above which you want to split the table. Then select Table Split Table. This splits the table into two by inserting an empty paragraph between the tables. It may be a good idea to turn on non-printing characters (Ctrl+Shift+8) so that you can see the paragraph marks. -- Regards Lene Fredborg DocTools - Denmark www.thedoctools.com Document automation - add-ins, macros and templates for Microsoft Word "springoflife" wrote: I have a very long table that spans the length of several pages. How can I split the table into multiple tables and have one table per page?
|
|
#5
December 13th, 2007, 09:52 PM
posted to microsoft.public.word.tables
|
|||
|
|||
|
How can I horizontally split a table (in WORD) into two tables
Sorry, my answer was for Word 2003 and older (you did mention Word 2007).
Follow the link below to open an interactive Word 2003 to Word 2007 command reference guide – it lets you point out commands in Word 2003 and will show you where to find the corresponding functionality in Word 2007: http://office.microsoft.com/en-us/wo...744321033.aspx -- Regards Lene Fredborg DocTools - Denmark www.thedoctools.com Document automation - add-ins, macros and templates for Microsoft Word "springoflife" wrote: Where is that option in WORD 2007? I can't find a "Split Table" command anywhere. ? "Lene Fredborg" wrote: Click in the row above which you want to split the table. Then select Table Split Table. This splits the table into two by inserting an empty paragraph between the tables. It may be a good idea to turn on non-printing characters (Ctrl+Shift+8) so that you can see the paragraph marks. -- Regards Lene Fredborg DocTools - Denmark www.thedoctools.com Document automation - add-ins, macros and templates for Microsoft Word "springoflife" wrote: I have a very long table that spans the length of several pages. How can I split the table into multiple tables and have one table per page?
|
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
