If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Nesting the roundup Function in a larger formula
=((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson
This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
#2
|
|||
|
|||
Nesting the roundup Function in a larger formula
=((((PI()*E22)*1.3)*0.377))*(CEILING(H22/J20))*TotalCaisson
or, with unnecessary parentheses removed =PI()*E22*1.3*0.377*CEILING(H22/J20)*TotalCaisson best wishes-- Bernard V Liengme Microsoft Excel MVP http://people.stfx.ca/bliengme remove caps from email "boxarox" wrote in message ... =((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
#3
|
|||
|
|||
Nesting the roundup Function in a larger formula
Bernard has given you the answer you asked for, but I have a question for my
own curiosity. You said E22 contained the circumference, so why are you multiplying by PI? Now, if E22 held the diameter, then I could understand multiplying by PI as PI*Diameter is the formula for circumference, but you said you already have the circumference; so what is the multiplication by PI doing? -- Rick (MVP - Excel) "boxarox" wrote in message ... =((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
#4
|
|||
|
|||
Nesting the roundup Function in a larger formula
Looks like you forgot to include the significance argument in the CEILING
function: =PI()*E22*1.3*0.377*CEILING(H22/J20,1)*TotalCaisson -- Biff Microsoft Excel MVP "Bernard Liengme" wrote in message ... =((((PI()*E22)*1.3)*0.377))*(CEILING(H22/J20))*TotalCaisson or, with unnecessary parentheses removed =PI()*E22*1.3*0.377*CEILING(H22/J20)*TotalCaisson best wishes-- Bernard V Liengme Microsoft Excel MVP http://people.stfx.ca/bliengme remove caps from email "boxarox" wrote in message ... =((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
#5
|
|||
|
|||
Nesting the roundup Function in a larger formula
Good eye Rick-- I had the math right, but wrote down the wrong description!
E22 actually contains the diameter. Thanks for your help. "Rick Rothstein" wrote: Bernard has given you the answer you asked for, but I have a question for my own curiosity. You said E22 contained the circumference, so why are you multiplying by PI? Now, if E22 held the diameter, then I could understand multiplying by PI as PI*Diameter is the formula for circumference, but you said you already have the circumference; so what is the multiplication by PI doing? -- Rick (MVP - Excel) "boxarox" wrote in message ... =((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
#6
|
|||
|
|||
Nesting the roundup Function in a larger formula
"Bernard Liengme" wrote: =((((PI()*E22)*1.3)*0.377))*(CEILING(H22/J20))*TotalCaisson or, with unnecessary parentheses removed =PI()*E22*1.3*0.377*CEILING(H22/J20)*TotalCaisson best wishes-- Bernard V Liengme Microsoft Excel MVP http://people.stfx.ca/bliengme remove caps from email "boxarox" wrote in message ... =((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
#7
|
|||
|
|||
Nesting the roundup Function in a larger formula
Thanks Bernard but We need to set the argument in the "Ceiling" portion of
the formula to "1". "Bernard Liengme" wrote: =((((PI()*E22)*1.3)*0.377))*(CEILING(H22/J20))*TotalCaisson or, with unnecessary parentheses removed =PI()*E22*1.3*0.377*CEILING(H22/J20)*TotalCaisson best wishes-- Bernard V Liengme Microsoft Excel MVP http://people.stfx.ca/bliengme remove caps from email "boxarox" wrote in message ... =((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
#8
|
|||
|
|||
Nesting the roundup Function in a larger formula
The subject of this post is right up your alley, isn't it?
-- Biff Microsoft Excel MVP "Rick Rothstein" wrote in message ... Bernard has given you the answer you asked for, but I have a question for my own curiosity. You said E22 contained the circumference, so why are you multiplying by PI? Now, if E22 held the diameter, then I could understand multiplying by PI as PI*Diameter is the formula for circumference, but you said you already have the circumference; so what is the multiplication by PI doing? -- Rick (MVP - Excel) "boxarox" wrote in message ... =((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
#9
|
|||
|
|||
Nesting the roundup Function in a larger formula
Whatever do you mean? g
-- Rick (MVP - Excel) "T. Valko" wrote in message ... The subject of this post is right up your alley, isn't it? -- Biff Microsoft Excel MVP "Rick Rothstein" wrote in message ... Bernard has given you the answer you asked for, but I have a question for my own curiosity. You said E22 contained the circumference, so why are you multiplying by PI? Now, if E22 held the diameter, then I could understand multiplying by PI as PI*Diameter is the formula for circumference, but you said you already have the circumference; so what is the multiplication by PI doing? -- Rick (MVP - Excel) "boxarox" wrote in message ... =((((PI()*E22)*1.3)*0.377))*((H22/J20))*TotalCaisson This is a formula for calculating the total weight of #3 rebar ties on a caisson Where E22=Caisson circumfrence in feet Where 1.30= the additional length required for overlap Where .377= the weight per foot of the tie. where H22 = Caisson Depth in feet where J20 = the rebar tie spacing in feet where TotalCaisson= the number caissons in the project of the given circumfrence I need to modify the formula so returns a whole number in the results of the H22/J20 portion of the calculation. So if the spacing of the ties is say, 1.17 feet and the depth of the caisson is 10 feet , the results of this portion of the formula is 9 rather than 8.547. (always rounded up to the next whole number) Can you help? |
Thread Tools | |
Display Modes | |
|
|