If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
I need to print a 2.5"x11" binder spine multiple times on 1 sheet
I have a binder spine doc that is 2.5 x 11", with 3 vertical columns to hold
the text and graphics in place. The page size is set as 2.5x11, so Word gets confused when I tell it I want to print several of these on one sheet of paper (to save on the expensive shiny paper I'm using). Anyone have any tips on how to print 2 or 3 of these on one sheet of paper? |
#2
|
|||
|
|||
I need to print a 2.5"x11" binder spine multiple times on 1 sheet
Leave the page size at 8.5 x 11, select Landscape orientation and set top
and bottom margins of 0.5 inch, then insert a three row one column borderless table in the document with the row height set to an exact figure of 2.5 inches and copy and paste whatever it is into each of the cells. -- Hope this helps. Please reply to the newsgroup unless you wish to avail yourself of my services on a paid consulting basis. Doug Robbins - Word MVP "Julesagain" wrote in message ... I have a binder spine doc that is 2.5 x 11", with 3 vertical columns to hold the text and graphics in place. The page size is set as 2.5x11, so Word gets confused when I tell it I want to print several of these on one sheet of paper (to save on the expensive shiny paper I'm using). Anyone have any tips on how to print 2 or 3 of these on one sheet of paper? |
#3
|
|||
|
|||
I need to print a 2.5"x11" binder spine multiple times on 1 sh
That did it!! Thanks so much for your help. I also had to set the header and
footer to zero to keep the page from leaking over into a new sheet, but this worked beautifully. Thank you, Julie Walker CAD/Graphics Georgia Trane "Doug Robbins - Word MVP" wrote: Leave the page size at 8.5 x 11, select Landscape orientation and set top and bottom margins of 0.5 inch, then insert a three row one column borderless table in the document with the row height set to an exact figure of 2.5 inches and copy and paste whatever it is into each of the cells. -- Hope this helps. Please reply to the newsgroup unless you wish to avail yourself of my services on a paid consulting basis. Doug Robbins - Word MVP "Julesagain" wrote in message ... I have a binder spine doc that is 2.5 x 11", with 3 vertical columns to hold the text and graphics in place. The page size is set as 2.5x11, so Word gets confused when I tell it I want to print several of these on one sheet of paper (to save on the expensive shiny paper I'm using). Anyone have any tips on how to print 2 or 3 of these on one sheet of paper? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How do I print multiple journal items in Memo Style on one sheet? | ABriscoe | General Discussions | 1 | October 27th, 2005 03:01 AM |
Print multiple pages per Sheet in Excel 2003 | Chris N | General Discussion | 1 | May 4th, 2005 03:17 AM |
How do I print the same sheet multiple times with increasing page. | C&S | General Discussion | 4 | March 31st, 2005 09:21 AM |
from a FORM print a label report 3 labels per sheet for CURRENT re | babs | Setting Up & Running Reports | 7 | February 6th, 2005 06:38 PM |
Charts print incorrectly in multiple sheet workbook | Bryan G. \(Indianapolis\) | Charts and Charting | 0 | November 14th, 2003 01:29 PM |