|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
June 21st, 2006, 05:49 PM
posted to microsoft.public.word.tables
|
|||
|
|||
How do I get shading to fill a table cell completely?
Sometimes when I shade a cell in a table it only partially fills the cell.
How can I fix this problem? 
|
|
#2
June 21st, 2006, 08:30 PM
posted to microsoft.public.word.tables
|
|||
|
|||
|
How do I get shading to fill a table cell completely?
Make sure you've shaded the cell itself and not the paragraph in it.
-- Suzanne S. Barnhill Microsoft MVP (Word) Words into Type Fairhope, Alabama USA Word MVP FAQ site: http://word.mvps.org Email cannot be acknowledged; please post all follow-ups to the newsgroup so all may benefit. "Anne" wrote in message ... Sometimes when I shade a cell in a table it only partially fills the cell. How can I fix this problem?
|
|
#3
June 21st, 2006, 08:50 PM
posted to microsoft.public.word.tables
|
|||
|
|||
|
How do I get shading to fill a table cell completely?
Thanks for the response! There is no text...it is an empty cell. Actually
there are 4 cells in one row; the 2 cells in the middle are highlighted correctly and the cells on each side are not--there is white space at the bottom. There also is no paragraph spacing or anything. "Suzanne S. Barnhill" wrote: Make sure you've shaded the cell itself and not the paragraph in it. -- Suzanne S. Barnhill Microsoft MVP (Word) Words into Type Fairhope, Alabama USA Word MVP FAQ site: http://word.mvps.org Email cannot be acknowledged; please post all follow-ups to the newsgroup so all may benefit. "Anne" wrote in message ... Sometimes when I shade a cell in a table it only partially fills the cell. How can I fix this problem?
|
|
#4
June 21st, 2006, 09:05 PM
posted to microsoft.public.word.tables
|
|||
|
|||
|
How do I get shading to fill a table cell completely?
In the Borders & Shading dialog, pay special attention to the "Apply
to" setting in the lower right. If it's set to Cell you should get shading that fills the cell. If it's set to Paragraph, there will be unshaded space between the text and the cell edges. -- Regards, Jay Freedman Microsoft Word MVP FAQ: http://word.mvps.org Email cannot be acknowledged; please post all follow-ups to the newsgroup so all may benefit. On Wed, 21 Jun 2006 09:49:02 -0700, Anne wrote: Sometimes when I shade a cell in a table it only partially fills the cell. How can I fix this problem?
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| three table database | ricardozelaya | Database Design | 3 | April 25th, 2006 12:15 AM |
| Multiple Options Group | Patty Stoddard | Using Forms | 19 | August 4th, 2005 02:30 PM |
| Possible Lookup Table | Karen | Worksheet Functions | 5 | June 8th, 2005 09:43 PM |
| Here's a shocker | Mike Labosh | General Discussion | 2 | October 26th, 2004 05:04 PM |
| Table Wizard Does Not Set Relationship if Foreign Key and Primary Key Name Do Not Match Exactly in Case. | HDW | Database Design | 3 | October 16th, 2004 03:42 AM |
Linear Mode
