If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Table of Contents - page numbering problem
Word 2003 -
The report has the following: physical page 1 - cover page physical page 2 - TOC physical page 3 - Executive Summary Pages 1 is in section one; Page 2 is in section 2 and 3 (section break continuous to allow us to add info under the TOC). The section break is to have no header on the Executive Summary but a header on the remaining pages. That header - which start on physical page four - says page 2, like we want it too. Here's the problem: the boss wants the Executive Summary to show up in the TOC as page 1. It wants to show up as page 2. The only way I got it to work was to tell the system to start that page on page 0. We are going to be doing lots of reports with the same format and this problem. I need to know if there is a better way than this since I don't understand why this works. Any light you can shed would be appreciated. Thanks |
#2
|
|||
|
|||
Table of Contents - page numbering problem
Hi =?Utf-8?B?U3V6YW4=?=,
You show us the physical pages, but not what the numbering should be on the physical pages. You also don't mention in which section the Executive Summary is. I'm also not clear on whether the boss expects this page number to be different from the number appearing in the TOC? And is there a really good reason why you use a continuous section break within the TOC page? You can add stuff under a TOC without putting it in a separate section... Word 2003 - The report has the following: physical page 1 - cover page physical page 2 - TOC physical page 3 - Executive Summary Pages 1 is in section one; Page 2 is in section 2 and 3 (section break continuous to allow us to add info under the TOC). The section break is to have no header on the Executive Summary but a header on the remaining pages. That header - which start on physical page four - says page 2, like we want it too. Here's the problem: the boss wants the Executive Summary to show up in the TOC as page 1. It wants to show up as page 2. The only way I got it to work was to tell the system to start that page on page 0. We are going to be doing lots of reports with the same format and this problem. I need to know if there is a better way than this since I don't understand why this works. Cindy Meister INTER-Solutions, Switzerland http://homepage.swissonline.ch/cindymeister (last update Sep 30 2003) http://www.word.mvps.org This reply is posted in the Newsgroup; please post any follow question or reply in the newsgroup and not by e-mail :-) |
#3
|
|||
|
|||
Table of Contents - page numbering problem
Your questions made me go back and revisit the section breaks that were in there. I took out the section break cont. under the TOC, put a section break next page, different header on first page, after the additional info under the TOC and that seemed to do the trick. I didn't do the original so I'm not sure what the rational is for some of the section breaks. (I think there's a training issue involved here)
If we do the TOC first and then add the information under it, will it stay out of the TOC when it is F9'd later? Since I modified it after the fact, I'm not sure what happens if you create it that way from scratch. Thanks for all your help!!!! |
#4
|
|||
|
|||
Table of Contents - page numbering problem
Hi =?Utf-8?B?U3V6YW4=?=,
Your questions made me go back and revisit the section breaks that were in there. I took out the section break cont. under the TOC, put a section break next page, different header on first page, after the additional info under the TOC and that seemed to do the trick. I didn't do the original so I'm not sure what the rational is for some of the section breaks. (I think there's a training issue involved here) If we do the TOC first and then add the information under it, will it stay out of the TOC when it is F9'd later? Since I modified it after the fact, I'm not sure what happens if you create it that way from scratch. What appears in the TOC depends on how the TOC is defined (styles? TC fields? outline levels?), and what is used in that "information under it". Since I have no idea, I can't give you an answer :-) Note that, as soon as one starts to mess with section breaks, a document could pick up some damage. t'ain't necessarily so, but the possibility exists; section breaks are fragile things... You might want to take a minute to set up a new document with the correct margins, then copy the content over section by section - leaving the section breaks and last paragraph mark behind. This means you'll also need to recreate the headers and footers and other section-specific elements. But the time spent now could save you from nasty, and expensive, surprises later on :-) Cindy Meister INTER-Solutions, Switzerland http://homepage.swissonline.ch/cindymeister (last update Sep 30 2003) http://www.word.mvps.org This reply is posted in the Newsgroup; please post any follow question or reply in the newsgroup and not by e-mail :-) |
#5
|
|||
|
|||
Table of Contents - page numbering problem
I pretty much did what you recommended and the report looks fine now. I also set up a procedure for fixing the two he is working on now and another procedure for how to do it all from scratch. I'm not sure who formatted the reports or told him how to do it but - I think we're okay until the next emergency. Thanks for all your help!
|
#6
|
|||
|
|||
Table of Contents - page numbering problem
Hi =?Utf-8?B?U3V6YW4=?=,
the report looks fine now. I also set up a procedure for fixing the two he is working on now and another procedure for how to do it all from scratch. good! Glad everything is up and running :-) Cindy Meister |
Thread Tools | |
Display Modes | |
|
|