If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
rtf2 lebans
i have installed rtf2 lebans control ver. 1.8. If i use un unbound control i have a problem when i transfer data from a memo table. I use: rtf2.RTFtext= memofield in recordset i have a message: RTF2: property is read only. After is Ok, but i don't know how can't display this message Thank you. |
#2
|
|||
|
|||
rtf2 lebans
You cannot populate an ActiveX control on a form or report before the
control is fully instantiated(created). The Event you are currently using is too early in the process. What event are you using? -- HTH Stephen Lebans http://www.lebans.com Access Code, Tips and Tricks Please respond only to the newsgroups so everyone can benefit. "A.C." wrote in message ... i have installed rtf2 lebans control ver. 1.8. If i use un unbound control i have a problem when i transfer data from a memo table. I use: rtf2.RTFtext= memofield in recordset i have a message: RTF2: property is read only. After is Ok, but i don't know how can't display this message Thank you. |
#3
|
|||
|
|||
rtf2 lebans
I use the event Form_Open.
"Stephen Lebans" ha scritto nel messaggio ... You cannot populate an ActiveX control on a form or report before the control is fully instantiated(created). The Event you are currently using is too early in the process. What event are you using? -- HTH Stephen Lebans http://www.lebans.com Access Code, Tips and Tricks Please respond only to the newsgroups so everyone can benefit. "A.C." wrote in message ... i have installed rtf2 lebans control ver. 1.8. If i use un unbound control i have a problem when i transfer data from a memo table. I use: rtf2.RTFtext= memofield in recordset i have a message: RTF2: property is read only. After is Ok, but i don't know how can't display this message Thank you. |
#4
|
|||
|
|||
rtf2 lebans
Change to Form Load.
-- HTH Stephen Lebans http://www.lebans.com Access Code, Tips and Tricks Please respond only to the newsgroups so everyone can benefit. "A.C." wrote in message ... I use the event Form_Open. "Stephen Lebans" ha scritto nel messaggio ... You cannot populate an ActiveX control on a form or report before the control is fully instantiated(created). The Event you are currently using is too early in the process. What event are you using? -- HTH Stephen Lebans http://www.lebans.com Access Code, Tips and Tricks Please respond only to the newsgroups so everyone can benefit. "A.C." wrote in message ... i have installed rtf2 lebans control ver. 1.8. If i use un unbound control i have a problem when i transfer data from a memo table. I use: rtf2.RTFtext= memofield in recordset i have a message: RTF2: property is read only. After is Ok, but i don't know how can't display this message Thank you. |
#5
|
|||
|
|||
rtf2 lebans
thank you.
alessandro. "Stephen Lebans" ha scritto nel messaggio ... Change to Form Load. -- HTH Stephen Lebans http://www.lebans.com Access Code, Tips and Tricks Please respond only to the newsgroups so everyone can benefit. "A.C." wrote in message ... I use the event Form_Open. "Stephen Lebans" ha scritto nel messaggio ... You cannot populate an ActiveX control on a form or report before the control is fully instantiated(created). The Event you are currently using is too early in the process. What event are you using? -- HTH Stephen Lebans http://www.lebans.com Access Code, Tips and Tricks Please respond only to the newsgroups so everyone can benefit. "A.C." wrote in message ... i have installed rtf2 lebans control ver. 1.8. If i use un unbound control i have a problem when i transfer data from a memo table. I use: rtf2.RTFtext= memofield in recordset i have a message: RTF2: property is read only. After is Ok, but i don't know how can't display this message Thank you. |
Thread Tools | |
Display Modes | |
|
|