If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
how do I add tab controls to a form
How do I add tabs to forms? I would like to a have a form that has 2 other
tabs that lead to other forms that should be linked together. |
#2
|
|||
|
|||
how do I add tab controls to a form
Put the form in designview and look in the menubar for the toolbox which has
a button on it which says tabcontrol click on it once and then click on your form. This should place a tabcontrol with two tabs on your form. -- Maurice Ausum "jo" wrote: How do I add tabs to forms? I would like to a have a form that has 2 other tabs that lead to other forms that should be linked together. |
#3
|
|||
|
|||
how do I add tab controls to a form
Just to add to Maurice's advice, here's a quick little tutorial I give people
on the use of Tabbed Pages. It addresses some of the common problems experienced with them: First thing to remember is that the Tabbed Pages are all part of a single form; think of it as a really long form turned on its side. Because it is all one form, all referencing to any control on it is done in the same manner as if they were all on one single screen. Create a form in Design View. Goto the toolbox and click on the Tabbed Control icon; it actually looks like several manila file folders. Place it on your form and adjust the size to your liking. If you need more than the two tabbed pages it initially gives you, click on the tabbed control to select it. Goto Insert and click on Tabbed Control Page and another tabbed page will be added. Do this as many times as necessary. This is the really important part: when you go to add a control to a tabbed page, whether it be a textbox, command button or subform, you must first click to select one of the pages, then add the control. Otherwise, the control will be added to the form itself, and will show thru on all tabbed pages! If a single page has been selected, when your cursor carrying the control appears over the page, a black "insert" will appear. Once you have the form's Control Source (your table or a query) set up, you simple add controls as you normally would, heeding the above paragraph. Also important to understand! If you go to move a control from one part of your main form to a tabbed page, you cannot drag and drop it! You must cut it, select the tabbed page, then paste it! And if the control has any code behind it, a GotFocus, OnClick, etc, after dropping it on the tabbed page, you'll have to "re-connect" it to its code. Select the control, goto Properties, click to the right of [Event Procedure] on whatever event to bring up the ellipsis (...) then click it to go to the code window. Exit the code editor and the control and its event code will be connected. One last thing. When trying to access the Properties of the Tabbed Control, such as the BackStyle, people complain that they can't find property. The problem is that they haven't selected the Tabbed Control, they've selected one of the pages of the Tabbed Control! The best way to be sure of selecting the Tabbed Control itself is to click to the right of the last tab. If you have 2 tabs, for instance, click in the blank area where Tab 3 would be, if you had a Tab 3. Maurice wrote: Put the form in designview and look in the menubar for the toolbox which has a button on it which says tabcontrol click on it once and then click on your form. This should place a tabcontrol with two tabs on your form. How do I add tabs to forms? I would like to a have a form that has 2 other tabs that lead to other forms that should be linked together. -- There's ALWAYS more than one way to skin a cat! Answers/posts based on Access 2000/2003 Message posted via AccessMonster.com http://www.accessmonster.com/Uwe/For...forms/200904/1 |
Thread Tools | |
Display Modes | |
|
|