If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Force a blank page
I have an application wherein I need to force a
blank page, sometimes at the beginning of the report and sometimes at the end. How do I do that? Bill |
#2
|
|||
|
|||
Force a blank page
The same report or different reports?
You could include a page break control and turn its visible property on and off with some vba. Another method would be to use a blank Report Header (not the page header) and force a page break after the Report header section. If your report is not using the Report footer you can force a page break after the Report footer. Also, do you mean completely blank (no page header or page footer) or do you mean no data between the two items. "Bill" wrote in message ink.net... I have an application wherein I need to force a blank page, sometimes at the beginning of the report and sometimes at the end. How do I do that? Bill |
#3
|
|||
|
|||
Force a blank page
John wrote:
Another method would be to use a blank Report Header (not the page header) and force a page break after the Report header section. How does one do that? In the ReportHeader_Format? ReportHeader_Print? Whichever the case, I don't see a command in the VBA help for that? By blank page, I mean "like" one was going to put a separator page between multiple copies of a printed report. Bill "John Spencer" wrote in message ... The same report or different reports? You could include a page break control and turn its visible property on and off with some vba. Another method would be to use a blank Report Header (not the page header) and force a page break after the Report header section. If your report is not using the Report footer you can force a page break after the Report footer. Also, do you mean completely blank (no page header or page footer) or do you mean no data between the two items. "Bill" wrote in message ink.net... I have an application wherein I need to force a blank page, sometimes at the beginning of the report and sometimes at the end. How do I do that? Bill |
#4
|
|||
|
|||
Force a blank page
Add a report header to the report
Set the Report Header's Force New Page property to After Section (on the format tab) If you have page header and footer sections with controls that print you will probably have to hide the controls when you are "printing" this page. That may require vba code to run that checks the page number (Page) and hides or shows the controls depending on the current page number. Bill wrote: John wrote: Another method would be to use a blank Report Header (not the page header) and force a page break after the Report header section. How does one do that? In the ReportHeader_Format? ReportHeader_Print? Whichever the case, I don't see a command in the VBA help for that? By blank page, I mean "like" one was going to put a separator page between multiple copies of a printed report. Bill "John Spencer" wrote in message ... The same report or different reports? You could include a page break control and turn its visible property on and off with some vba. Another method would be to use a blank Report Header (not the page header) and force a page break after the Report header section. If your report is not using the Report footer you can force a page break after the Report footer. Also, do you mean completely blank (no page header or page footer) or do you mean no data between the two items. "Bill" wrote in message ink.net... I have an application wherein I need to force a blank page, sometimes at the beginning of the report and sometimes at the end. How do I do that? Bill |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
I cant get my report to fit on one page | rmoritzky | Setting Up & Running Reports | 16 | February 10th, 2009 01:35 PM |
Report w/3 subreports - getting unnecessary/unwanted blank page | Heart-of-Dixie | Setting Up & Running Reports | 3 | September 19th, 2005 05:23 PM |
Cannot force page # | klam | General Discussion | 3 | October 22nd, 2004 09:59 PM |
Creating an "unmovable" blank page | Dan | Page Layout | 1 | October 11th, 2004 11:12 PM |
How to delete a blank page between the pages. | Suzanne S. Barnhill | General Discussion | 2 | May 17th, 2004 11:06 AM |