If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Cannot save design changes in table/report in Access 2007
Hi,
I have done this before, but suddenly I seem to be unable to save changes to the design of forms and reports. Nobody else is accessing the database. I can push save, but when I then click on close form/report I get the messsage asking if I want to save before closing. If I then press yes, the saving message disappears but the form/report is still open. If I want to close it again, the same message pops up. The only way to get out is by pressing don't save changes, but then the changes I made to the design were not changed. I have been able to make design changes before, does anyone know what might have happened? |
#2
|
|||
|
|||
Cannot save design changes in table/report in Access 2007
Run this basic recovery sequence:
http://allenbrowne.com/recover.html If you are still stuck, create a new database, create a form in it, and see if it has the same problem. -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. "ningi" wrote in message ... Hi, I have done this before, but suddenly I seem to be unable to save changes to the design of forms and reports. Nobody else is accessing the database. I can push save, but when I then click on close form/report I get the messsage asking if I want to save before closing. If I then press yes, the saving message disappears but the form/report is still open. If I want to close it again, the same message pops up. The only way to get out is by pressing don't save changes, but then the changes I made to the design were not changed. I have been able to make design changes before, does anyone know what might have happened? |
#3
|
|||
|
|||
Cannot save design changes in table/report in Access 2007
I have the same issue. I have tried the recovery sequence and it did not correct the problem. I have tried splitting the database and it did not correct the problem. I tried creating a new database and importing the forms and reports from the split database and nearly every item failed. If I create a new database with mock information, then I can save design changes to the report. My database has 12 reports and 16 forms... is there any way around recreating them all?
Allen Browne wrote: Run this basic recovery sequence:http://allenbrowne.com/recover. 12-Feb-10 Run this basic recovery sequence: http://allenbrowne.com/recover.html If you are still stuck, create a new database, create a form in it, and see if it has the same problem. -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. Previous Posts In This Thread: On Friday, February 12, 2010 1:51 AM ningi wrote: Cannot save design changes in table/report in Access 2007 Hi, I have done this before, but suddenly I seem to be unable to save changes to the design of forms and reports. Nobody else is accessing the database. I can push save, but when I then click on close form/report I get the messsage asking if I want to save before closing. If I then press yes, the saving message disappears but the form/report is still open. If I want to close it again, the same message pops up. The only way to get out is by pressing do not save changes, but then the changes I made to the design were not changed. I have been able to make design changes before, does anyone know what might have happened? On Friday, February 12, 2010 2:46 AM Allen Browne wrote: Run this basic recovery sequence:http://allenbrowne.com/recover. Run this basic recovery sequence: http://allenbrowne.com/recover.html If you are still stuck, create a new database, create a form in it, and see if it has the same problem. -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. Submitted via EggHeadCafe - Software Developer Portal of Choice Using VSTO Add-In To Automate Frequent Excel 2007 Tasks http://www.eggheadcafe.com/tutorials...n-to-auto.aspx |
#4
|
|||
|
|||
Cannot save design changes in table/report in Access 2007
Have you verified there is no problem with references?
Did you try the SaveAsText/LoadFromText with any of the broken forms? -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. "Laurel Walters" wrote in message ... I have the same issue. I have tried the recovery sequence and it did not correct the problem. I have tried splitting the database and it did not correct the problem. I tried creating a new database and importing the forms and reports from the split database and nearly every item failed. If I create a new database with mock information, then I can save design changes to the report. My database has 12 reports and 16 forms... is there any way around recreating them all? Allen Browne wrote: Run this basic recovery sequence:http://allenbrowne.com/recover. 12-Feb-10 Run this basic recovery sequence: http://allenbrowne.com/recover.html If you are still stuck, create a new database, create a form in it, and see if it has the same problem. -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. Previous Posts In This Thread: On Friday, February 12, 2010 1:51 AM ningi wrote: Cannot save design changes in table/report in Access 2007 Hi, I have done this before, but suddenly I seem to be unable to save changes to the design of forms and reports. Nobody else is accessing the database. I can push save, but when I then click on close form/report I get the messsage asking if I want to save before closing. If I then press yes, the saving message disappears but the form/report is still open. If I want to close it again, the same message pops up. The only way to get out is by pressing do not save changes, but then the changes I made to the design were not changed. I have been able to make design changes before, does anyone know what might have happened? On Friday, February 12, 2010 2:46 AM Allen Browne wrote: Run this basic recovery sequence:http://allenbrowne.com/recover. Run this basic recovery sequence: http://allenbrowne.com/recover.html If you are still stuck, create a new database, create a form in it, and see if it has the same problem. -- Allen Browne - Microsoft MVP. Perth, Western Australia Tips for Access users - http://allenbrowne.com/tips.html Reply to group, rather than allenbrowne at mvps dot org. Submitted via EggHeadCafe - Software Developer Portal of Choice Using VSTO Add-In To Automate Frequent Excel 2007 Tasks http://www.eggheadcafe.com/tutorials...n-to-auto.aspx |
Thread Tools | |
Display Modes | |
|
|