|
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|||||||
|
|
Thread Tools | Display Modes |
|
#1
July 10th, 2009, 09:00 AM
posted to microsoft.public.visio.general
|
|||
|
|||
Barch converting of eps or dxf files.
http://www.merten.de/cgi-bin/dwl.cgi...xe&&read=didnt
Those are the symbols in the KNX domotics standard. First I thought making them myself. But this is not so straightforward because of the resize issue with text. Does anyone know how to convert these files en masse ? And, no, Sandrila does not have them. 
|
|
#2
July 10th, 2009, 10:28 AM
posted to microsoft.public.visio.general
|
|||
|
|||
|
Barch converting of eps or dxf files.
On Fri, 10 Jul 2009 01:00:01 -0700, philippe c
wrote: http://www.merten.de/cgi-bin/dwl.cgi...xe&&read=didnt Those are the symbols in the KNX domotics standard. First I thought making them myself. But this is not so straightforward because of the resize issue with text. Does anyone know how to convert these files en masse ? And, no, Sandrila does not have them. I've never seen symbols like that! Nearest I have are the IEC417 symbols. Anyway, I managed to convert the DXF files to EMF format using Paint Shop Pro, has a batch mode, only took a minute. -- Regards, Paul Herber, Sandrila Ltd. Electronics for Visio http://www.electronics.sandrila.co.uk/ Electrical for Visio http://www.electrical.sandrila.co.uk/ Electronics Packages for Visio http://www.electronics-packages.sandrila.co.uk/
|
|
#3
July 10th, 2009, 01:20 PM
posted to microsoft.public.visio.general
|
|||
|
|||
|
Barch converting of eps or dxf files.
On Fri, 10 Jul 2009 10:28:18 +0100, Paul Herber
wrote: On Fri, 10 Jul 2009 01:00:01 -0700, philippe c wrote: http://www.merten.de/cgi-bin/dwl.cgi...xe&&read=didnt Those are the symbols in the KNX domotics standard. First I thought making them myself. But this is not so straightforward because of the resize issue with text. Does anyone know how to convert these files en masse ? And, no, Sandrila does not have them. I've never seen symbols like that! Nearest I have are the IEC417 symbols. Anyway, I managed to convert the DXF files to EMF format using Paint Shop Pro, has a batch mode, only took a minute. They compess quite well (to just under 1/2 MB) so I've put them at http://www.sandrila.co.uk/binaries/EIB.zip -- Regards, Paul Herber, Sandrila Ltd. Electronics for Visio http://www.electronics.sandrila.co.uk/ Electrical for Visio http://www.electrical.sandrila.co.uk/ Electronics Packages for Visio http://www.electronics-packages.sandrila.co.uk/
|
|
#4
July 10th, 2009, 01:35 PM
posted to microsoft.public.visio.general
|
|||
|
|||
|
Barch converting of eps or dxf files.
On Fri, 10 Jul 2009 01:00:01 -0700, philippe c
wrote: http://www.merten.de/cgi-bin/dwl.cgi...xe&&read=didnt Those are the symbols in the KNX domotics standard. First I thought making them myself. But this is not so straightforward because of the resize issue with text. Does anyone know how to convert these files en masse ? And, no, Sandrila does not have them. Philippe, the email address you used to post on the contact form on my website bounces. -- Regards, Paul Herber, Sandrila Ltd. DFD/SSADM for Visio http://www.visio-dfd.sandrila.co.uk/ Now in English, Dutch, French, Portuguese and Spanish
|
|
#5
July 10th, 2009, 02:45 PM
posted to microsoft.public.visio.general
|
|||
|
|||
|
Barch converting of eps or dxf files.
Thank you.
"Paul Herber" wrote: On Fri, 10 Jul 2009 10:28:18 +0100, Paul Herber wrote: On Fri, 10 Jul 2009 01:00:01 -0700, philippe c wrote: http://www.merten.de/cgi-bin/dwl.cgi...xe&&read=didnt Those are the symbols in the KNX domotics standard. First I thought making them myself. But this is not so straightforward because of the resize issue with text. Does anyone know how to convert these files en masse ? And, no, Sandrila does not have them. I've never seen symbols like that! Nearest I have are the IEC417 symbols. Anyway, I managed to convert the DXF files to EMF format using Paint Shop Pro, has a batch mode, only took a minute. They compess quite well (to just under 1/2 MB) so I've put them at http://www.sandrila.co.uk/binaries/EIB.zip -- Regards, Paul Herber, Sandrila Ltd. Electronics for Visio http://www.electronics.sandrila.co.uk/ Electrical for Visio http://www.electrical.sandrila.co.uk/ Electronics Packages for Visio http://www.electronics-packages.sandrila.co.uk/
|
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
